raingutter regatta sail tips

reginehenkle19925 Maret 16, 2022 raingutter , regatta , tips Comment

Let your scout decorate the hull and sail insert the mast and attach the sail. Cup sail modifications will be faster than the standard sail Appendix B.

Make The Ultimate Raingutter Regatta Racer Scout Life Magazine

Zaiden builds his Rain Gutter Regatta for Cub Scouts.

. Wolfs rac e at 300pm. Too high and your boat will. If the sail is too low the corners rub against the gutter or dip in the water.

Standard gutter-length is 10 feet. Standard BSA kit construction tips. Special thanks to the other.

Lions race at 200pm. The Outriggers must be no longer than 7 or shorter than 6 ½. Ensure the rudder is flat.

The traditional Raingutter Regatta uses 10 gutters with end caps attached. NO substitutions are allowed OutriggersHull. Nothing may extend past front point or rear point of outriggers so maximum total boat length is 6 34 inches Maximum boat hull width not counting sail is 3 38 inches if you have parts sticking out from sides you will hit the gutter and go slow Must use all parts from kit 2 outriggers trimaran hull 4 screws mast and sail No.

Supplies to Build Boats. Tips on Building a Raingutter Regatta. If youre not sure of what this raingutter regatta exactly it is a quick video.

Material For Double Raceway. Racing will start at 200 PM sharp and will be done by Den level starting with the Lions and ending with Arrow of Light. This minimizes tipping when you blow during race Mast in front of Mast sail behind sail 1.

Only Official BSA Raingutter Regatta kits are to be used. As close to the. Attach bottom of sail in a similar manner.

The best sailing boat may be a raw un-finished boat with the mast and sail stuck on. 2 - Trough supports 1 X 4 X 36 cut so gutter will fit. The bottom edge of the sail needs to be about 12 inch above the deck of the boat.

Lower the sail so that it touches the deck. These Raingutter boats can be built the same day they are raced or taken home to build or built as a group during a meeting. For best results paint or otherwise seal the hulls of the boat that will be touching the water.

The vertical position of the sale is important. It can be cardio-challenging. This is done by attaching a thread to the lower corners of the sail and pulling them back.

Webelos rac e at 400pm. Preheat your oven to 250 degrees. Trim the hull to make it symmetrical.

AoL rac e at. This helps keep the sail from touching the sides of the raingutter as well as providing stabilization of the sail as it catches the air. Raingutter Regatta Rules and TipsHints Sheet.

Bears rac e at 330pm. Try to keep the bottom as flat as possible. Making a boat is very easy.

Two things the Raingutter Regatta requires each participant to learn are 1 the craft skills necessary to build a boat and 2 the rules that must be followed. The hull is 2 12 wide and the sail is 2 12 wideThe hull is made of Dow Corning Styrofoam. Be sure to keep these important points in mind while you build your boat.

Trim excess weight off everything and be careful how much you add like decorations and paint. The boys should do the majority of the design and work sandpaper can be used to shape the hull and no power tools should be required. As our Raingutter Regatta race gets closer here are a few pages that have some cool tips on boat making.

4 - End caps for gutter rivets or bolts to end. The sail provided in the BSA. Push the sail down the mast as far as it will go.

Fold the sail toward the back of boat along the two red lines so that it does not extend past the outriggers. How to Make Recycled Raingutter Regatta Boats. Boats must be made from the official BSA Raingutter Regatta Trimaran Boat Kit.

Each scout has an assigned boat number printed on a label affixed to your boat kit. Contrary to popular belief the balsa pontoons should not have a V-shaped keel. Sail touches hull 2.

Use a bit of glue or tape on the mast and sail so they dont come out or spin when blown on. Raingutter Regatta Tips Pack 410 1. Put your boat number on the sail - youre done.

Place the Pinewood Derby block of wood on the cookie sheet. For each type of. LET THE BOYS DO IT.

Michael Spitler has some great fresh ideas on design click through. This foam is a closed cell foam. The threads are then tied to a straight pin that is inserted in the middle rear of the boat.

Place the cookie sheet with the block of wood into the oven. This is called sportsmanship. Even more important though is how we act and behave while participating in the Raingutter Regatta or any other group activity.

A bent rudder will steer the boat into the raingutter. This is an excellent place for decals and stickersboys love both. The mast may be placed in any position on the top of the boat and the sail may be arched or curved in one dimension only.

The boys and an adult should make the boat together. Sail must be upright for its entire length and must be attached to the mast supplied with the kit. Position the sail on the mast.

2 - End braces 1 X 4 X 23 2 - Diagonal braces 1 X 2 X 72 4 - Legs 2 X 2 X 34. Vinyl gutters are better because they wont bend. The cars speed is increased by placing the weight at specific spotsRemoving moisture from the block of wood will allow weight to be placed in the back of the car as well as the underside.

SAIL - Supplied in kit - no alterations to size allowed. How to Build a Raingutter Regatta Boat for Boy Scouts. Each Rainspout Sailboat kit comes with 1 hull 1 mast 1 rudder and a sail.

The boat races take place in two rain gutters filled with water that are placed side-by-side on a long table. About 34 from the top of the mast either glue the sail to it or attach securely with tape. He researched many videos and made his own version of the winning regattas.

Here are a few speed tips to put you in front of the pack. Please pay attention to race times below and arrive early. Fold sail to rear 1.

The two skippers place their boats at the starting end and propel them to the finish line by blowing air through a straw aimed at the sail. The sail may be tied tacked or glued in place as long as it is upright and unfolded. This prevents dragging on the gutter sides.

2 - 10 foot lengths of 5 diameter half round gutter. You do want to glue your sail in placeat the very minimum and having flat rails on the bottom helps. An area to show off your decorations is on the sail.

Instead they should. Tigers rac e at 230pm. Glue sail to deck.

Regatta Racing Schedule. Siblings rac e at 245pm. All parts 2 outriggers polymer hull mast sail and 4 screws provided in the kit must be used in the boat construction.

Make An Award Winning Raingutter Regatta Trimaran Boat Kit By Michael Spitler Michaelspitler